FAQ - Frequently Asked Questions
- Products Search > Materials Testing & Inspection
Keyword Search
Materials Testing & Inspection
Frequently Referenced FAQ
FAQ within [ Materials Testing & Inspection ]
-
(EZ-Test) Inspection of Test Force
Check wheter the test force is approximately correct or not. 1. Prepare the test force calibration jig. 2. Insert the joint for UJ into the bo ttom... Show Detail
- No：7705
- Date of Issue：2022/01/20 14:21
- Last Updated：2022/01/20 14:35
- Category： EZ-Test Series
-
(AGS-X) Inspection of Safety Equipment
1.While pressing a jog button to move the crosshead, press the emergency stop button. 2.The crosshead should stop and not restart, even if the jog button is... Show Detail
- No：8005
- Date of Issue：2022/01/20 14:07
- Category： AGS-X Series
- Brached FAQ
-
(EZ-Test) Inspection of Safety Equipment
1.While pressing a jog button to move the crosshead, press the emergency stop button. 2.The crosshead should stop and not restart, even if the jog button is... Show Detail
- No：7703
- Date of Issue：2022/01/20 14:07
- Category： EZ-Test Series
- Brached FAQ
-
(AGS-X) Attaching Specimens (Bending Test)
1. Adjust the distance between supports. 2. Place the specimen in the center of thesupports. 3. Use jog operations to move the bendingpunch a little above ... Show Detail
- No：8003
- Date of Issue：2022/01/20 13:37
- Category： AGS-X Series
-
(EZ-Test) Attaching Specimens (Bending Test)
1. Adjust the distance between supports. 2. Place the specimen in the center of thesupports. 3. Use jog operations to move the bendingpunch a little above ... Show Detail
- No：7701
- Date of Issue：2022/01/20 13:37
- Category： EZ-Test Series
-
(AGS-X) Setting Crosshead Stroke Limits
To prevent the crosshead (or attached load cells or jigs) from colliding with anything, secureupper and lower limit collars at respective crosshead upper and... Show Detail
- No：8001
- Date of Issue：2022/01/20 13:29
- Category： AGS-X Series
-
(EZ-Test) Setting Crosshead Stroke Limits
To prevent the crosshead (or attached load cells or jigs) from colliding with anything, secureupper and lower limit collars at respective crosshead upper and... Show Detail
- No：7699
- Date of Issue：2022/01/20 13:29
- Category： EZ-Test Series
-
(AGS-X) Attaching Compression and Bending Test Jigs
1. Screw in the compression loading jig. 2.Temporarily loosen the set bolt, theninsert the upper compression plate. 3.Insert the boss on the lowercompr... Show Detail
- No：7999
- Date of Issue：2022/01/20 11:26
- Category： AGS-X Series
- Brached FAQ
-
(EZ-Test) Attaching Compression and Bending Test Jigs
« For load cell with 1kN or larger capacity» 1. Attaching the compression load jig Screwtighten the compression loadjig of type (a) or (b) (see the fi... Show Detail
- No：7697
- Date of Issue：2022/01/20 11:26
- Category： EZ-Test Series
- Brached FAQ
-
1. Attaching the Specimen 1) Insert the specimen at thecenter of the grip faces. 2) Tighten securely with bothhands. 3) Use jog operations to... Show Detail
- No：7997
- Date of Issue：2022/01/20 10:55
- Category： AGS-X Series
31-40 of Total 211