Click [PURGE] to purge the bubbles. Alternatively, connect a syringe to the drain tube connection port to suction out th

Check for leakage from cell inlet and outlet pipe connections and from the cell window. If there is leakage, disassemble

Inspect the suction filter for blockage. Also rinse them as described below. 1) Flush with 17 % aqueous phosphate sol

Inspect the suction filter for blockage.Also rinse them as described below. 1) Flush with 17 % aqueous phosphate solu

Check the column using known analytical conditions. If the column has deteriorated, replace it. Confirm whether the so

Check the column using known analytical conditions. If the column has deteriorated, replace it. Connect the tubing cor

Pump 2-propanol to rinse the check valve. However, if a buffer solution is being used, rinse the check valve with purifi

Disassemble and clean the high pressure valve. If disassembled cleaning is not effective, then replace the rotor and sta

Confirm whether the baseline changes significantly when the cell outlet pipe is blocked. Alternatively, visually check f

Make sure the connector is connected securely. Specify an appropriate cell temperature-control temperature. The cell t

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > HPLC

Keyword Search

HPLC

Frequently Referenced FAQ

Latest FAQ

FAQ within [ HPLC ]

91-100 of Total 941

≪ 10 / 95page ≫

The baseline undulates with the pump stroke

Click [PURGE] to purge the bubbles. Alternatively, connect a syringe to the drain tube connection port to suction out the bubbles. Click here for Manual P... Show Detail
- No：4296
- Date of Issue：2020/12/03 11:00
- Category： Common , Solvent Delivery Module
- Brached FAQ
The baseline shifts

Check for leakage from cell inlet and outlet pipe connections and from the cell window. If there is leakage, disassemble and clean the cell. If there is lo... Show Detail
- No：4295
- Date of Issue：2020/12/03 10:59
- Category： Common
- Brached FAQ
The baseline drifts

Inspect the suction filter for blockage. Also rinse them as described below. 1) Flush with 17 % aqueous phosphate solution for about 30 minutes at a flowr... Show Detail
- No：4294
- Date of Issue：2020/12/03 10:57
- Category： Common , Detector , Solvent Delivery Module
- Brached FAQ
Ghost peaking occurs

Inspect the suction filter for blockage.Also rinse them as described below. 1) Flush with 17 % aqueous phosphate solution for about 30 minutes at a flowra... Show Detail
- No：4293
- Date of Issue：2020/12/03 10:52
- Category： Common , Autosampler , Solvent Delivery Module
- Brached FAQ
No peaks are output

Check the column using known analytical conditions. If the column has deteriorated, replace it. Confirm whether the solvent delivery pump is functioning pr... Show Detail
- No：4292
- Date of Issue：2020/12/03 10:49
- Category： Common , Autosampler , Column Oven , Detector , Solvent Delivery Module
- Brached FAQ
The peak shape is abnormal

Check the column using known analytical conditions. If the column has deteriorated, replace it. Connect the tubing correctly. Backflush the high pressure... Show Detail
- No：4291
- Date of Issue：2020/12/03 10:46
- Category： Common , Autosampler , Column Oven
- Brached FAQ
Peak retention times vary

Pump 2-propanol to rinse the check valve. However, if a buffer solution is being used, rinse the check valve with purified water first. Then rinse it by pump... Show Detail
- No：4290
- Date of Issue：2020/12/03 10:43
- Category： Common , Autosampler , Column Oven , Solvent Delivery Module
- Brached FAQ
The pressure change is large when high pressure valve swi...

Disassemble and clean the high pressure valve. If disassembled cleaning is not effective, then replace the rotor and stator. Contact a Shimadzu sales or se... Show Detail
- No：4289
- Date of Issue：2020/12/03 10:38
- Category： Autosampler
- Brached FAQ
Light level is low

Confirm whether the baseline changes significantly when the cell outlet pipe is blocked. Alternatively, visually check for any bubbles flowing in the flow ce... Show Detail
- No：4288
- Date of Issue：2020/12/03 10:36
- Category： Detector
- Brached FAQ
Cell Temperature Control Failure

Make sure the connector is connected securely. Specify an appropriate cell temperature-control temperature. The cell temperature-control setting range vari... Show Detail
- No：4287
- Date of Issue：2020/12/03 10:34
- Category： Detector
- Brached FAQ

91-100 of Total 941

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.