• The ICPEinstallation location does not meetrequirements related to installation location or facilities. • One of the

• Wipe off the water droplets with gauze or some otherappropriate material and ignite the plasma. • Checks that the ins

• The blank liquid is dirty. • The torch is dirty. • The chamber is dirty. Click here for "Replacing and Inspecti

1. Insert the nozzle (Parts number: 206-50290-91) into the nozzle hole located on the arm. 2. Lower the nozzle tip by

If the flow rate of the peristaltic pump used to supply rinse solution decreases, replace the tubing in the peristaltic

If the filter is clogged, remove the cover on the left side of the ASC-9800 and clean the filter. If the filter has det

WARNING: You may a burn. Don't touch the exhaust pipe on a plasma stand, or don't look in. 1) Argon gas pressure

WARNING:You may get a burn. Before starting the procedures below, turn OFF theplasma and wait until the water cooled jac

1.Cleaning part (1) Sheet copper connected with RF coil and the connecting part (2) Connecting part of this sheet co

NOTE: Cleaning the orifice prevents contamination of a sample and abnormaldischarge. WARNING:Never touch the inside o

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > Elemental Analysis

Keyword Search

Elemental Analysis

Frequently Referenced FAQ

Latest FAQ

FAQ within [ Elemental Analysis ]

111-120 of Total 132

≪ 12 / 14page ≫

(ICPE) The spectral intensity is unstable

• The ICPEinstallation location does not meetrequirements related to installation location or facilities. • One of the causes listed for problem "The spectr... Show Detail
- No：6737
- Date of Issue：2021/07/30 10:11
- Category： Multi type(ICPE)
(ICPE) Condensation occurs on the RF coil or the cooling ...

• Wipe off the water droplets with gauze or some otherappropriate material and ignite the plasma. • Checks that the installation location meets the installa... Show Detail
- No：6738
- Date of Issue：2021/07/30 10:11
- Last Updated：2021/10/04 10:07
- Category： Multi type(ICPE)
(ICPE) The spectral intensity for elements is high even w...

• The blank liquid is dirty. • The torch is dirty. • The chamber is dirty. Click here for "Replacing and Inspecting Glassware, Sample Introduction Tub... Show Detail
- No：6739
- Date of Issue：2021/07/30 10:11
- Category： Multi type(ICPE)
(ICPE) Mounting the Nozzle (Autosampler)

1. Insert the nozzle (Parts number: 206-50290-91) into the nozzle hole located on the arm. 2. Lower the nozzle tip by 103 mm from the bottom of the arm an... Show Detail
- No：6740
- Date of Issue：2021/08/03 10:21
- Category： Multi type(ICPE)
- Brached FAQ
(ICPE) Replacing the Peristaltic Pump Tubing (Autosampler)

If the flow rate of the peristaltic pump used to supply rinse solution decreases, replace the tubing in the peristaltic pump according to the following proce... Show Detail
- No：6741
- Date of Issue：2021/08/03 10:51
- Category： Multi type(ICPE)
- Brached FAQ
(ICPE) Filter Cleaning and Replacement (Autosampler)

If the filter is clogged, remove the cover on the left side of the ASC-9800 and clean the filter. If the filter has deteriorated, replace it with a new filt... Show Detail
- No：6742
- Date of Issue：2021/08/03 10:56
- Category： Multi type(ICPE)
- Brached FAQ
(ICPS) Operation Check of Safety Device

WARNING: You may a burn. Don't touch the exhaust pipe on a plasma stand, or don't look in. 1) Argon gas pressure switch If you stop supplying argo... Show Detail
- No：6766
- Date of Issue：2021/08/18 12:48
- Category： Sequential type(ICPS)
- Brached FAQ
(ICPS) Cleaning of Folding Mirror for Axial Observation(I...

WARNING:You may get a burn. Before starting the procedures below, turn OFF theplasma and wait until the water cooled jacket is cooled sufficiently (at least3... Show Detail
- No：6768
- Date of Issue：2021/08/18 14:50
- Category： Sequential type(ICPS)
(ICPS) Maintenance in the plasma stand(ICPS-7510)

1.Cleaning part (1) Sheet copper connected with RF coil and the connecting part (2) Connecting part of this sheet copper and matching-Box.And the circumf... Show Detail
- No：6770
- Date of Issue：2021/08/18 15:04
- Category： Sequential type(ICPS)
(ICPS) Cleaning of Orifice for Axial Observation(ICPS-7510)

NOTE: Cleaning the orifice prevents contamination of a sample and abnormaldischarge. WARNING:Never touch the inside of the stand for three minutes after e... Show Detail
- No：6769
- Date of Issue：2021/08/18 15:05
- Last Updated：2022/01/17 15:47
- Category： Sequential type(ICPS)

111-120 of Total 132

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.