FAQ - Frequently Asked Questions
- Products Search > GC-MS
Keyword Search
Frequently Referenced FAQ
FAQ within [ GC-MS ]
-
(GCMS) Chemical Ionization(CI, NCI) Reagent Gas Setup Pro...
Parts Number: 225-07776-91 PLUG KIT (Used as a stop cock when no reagent gas is used.) 1. Automatically stop the GC/MS in GCMSsolution. Wait until t... Show Detail
- No：4688
- Date of Issue：2020/12/17 13:08
- Category： Setting
-
(GCMS) Chemical Ionization(CI, NCI) When signal intensit...
Cause 1: Either the cylinder valve of the gas cylinder, the control knob of the pressure regulator, or the outlet valve of the pressure regulator is closed. ... Show Detail
- No：4703
- Date of Issue：2020/12/17 12:59
- Category： Troubleshooting
-
(GCMS) Chemical Ionization(CI, NCI) When good spectrum ca...
There may be leak of the reagent gas if the conditionsare not satisfied in spite that the reagent gas is being supplied. The possible causes of leak are desc... Show Detail
- No：4702
- Date of Issue：2020/12/17 12:59
- Category： Troubleshooting
-
(GCMS) DI-2010 Operation Methods
Parts Number: 225-04209 CAP(Cap for the DI-2010) 225-09344 SAMPLE VIAL 100 PC (DI-2010 standard accessories (10 pcs):Sample pot made of Pyrex) 225-0... Show Detail
- No：4701
- Date of Issue：2020/12/17 12:45
- Category： Setting
-
(GCMS) Guard Column Installation
1. Cut the deactivated fused silica tube (guard column) to approx. 2 m. 2. Using the capillary cutter, cut the connecting sections of the guard c... Show Detail
- No：7236
- Date of Issue：2020/12/17 10:18
- Category： Maintenance
-
1. Automatically stop the GC/MS. Wait until the "system shutdown" message appears. 2.Pull the column oven door latch toward you. 3.... Show Detail
- No：7234
- Date of Issue：2020/12/17 10:18
- Category： Maintenance
-
(GCMS) Reagent Gas Cylinder Replacement Procedure
Replace the reagent gas cylinder by following the procedure below. The instrument need not be stopped to perform this procedure. 1. Click [Tuning] on ... Show Detail
- No：4687
- Date of Issue：2020/12/17 10:18
- Category： Maintenance
-
(GCMS) Chemical Ionization(CI, NCI) Excessive Introductio...
Sometimes too much reagent gas is introduced during reagent gas adjustment. If this happens, extract excess reagent gas by following the procedure below. ... Show Detail
- No：4689
- Date of Issue：2020/12/17 10:16
- Category： Troubleshooting
-
(GCMS) Rotary Pump Oil Replacement Procedure (GHD-031)
Part Number: 225-38992-02OIL,ULVOIL R-2,1L(1L) 0.37L is necessary for each replacement. CAUTION: Wear safety glasses. 1. The photo on the le... Show Detail
- No：8981
- Date of Issue：2020/12/15 14:45
- Category： Maintenance
-
(GCMS) DI-2010 PTFE Seal and O-Ring Replacement Procedure
Parts Number: 225-01242-91: PLUG ASSY (Use it as a stopper when the DI-2010 is not used.) 225-10653-91: POSITIONING JIG (Tool to adjust the position of... Show Detail
- No：4694
- Date of Issue：2020/12/15 14:45
- Category： Maintenance
41-50 of Total 56