FAQ - Frequently Asked Questions
- Products Search > Non-Destructive Testing (NDT) Systems
Keyword Search
Non-Destructive Testing (NDT) Systems
Frequently Referenced FAQ
FAQ within [ Non-Destructive Testing (NDT) Systems ]
-
(SMX-1010/1020) Performing the Pre-Operation Check and In...
In the pre-operation check and initialization process, you will check the front door, returnthe stage to its origin, and perform the aging of the X-ray gener... Show Detail
- No：8617
- Date of Issue：2022/04/28 13:34
- Category： Xslicer SMX-1010/1020
-
(SMX-6010) Performing the Pre-Operation Check/Initialization
The pre-operation check/initialization involves checking the front door, checking the X-raygenerator, and returning the stage to the origin point. Perform th... Show Detail
- No：8591
- Date of Issue：2022/04/28 13:34
- Category： Xslicer SMX-6010
-
(SMX-6010) Replacing the Filament
NOTE: • Use this function in administrator mode. Click here for "(SMX-6010) Switching to Administrator Mode". • Even when [Status] under [Fila... Show Detail
- No：8595
- Date of Issue：2022/04/28 13:30
- Category： Xslicer SMX-6010
- Brached FAQ
-
(SMX-6010) Cleaning the Vacuum Chamber
When X-ray output is difficult, the interior of the vacuum chamber may be dirty causingelectrical discharges. In this case, clean the interior of the vacuum ... Show Detail
- No：8605
- Date of Issue：2022/04/28 13:28
- Category： Xslicer SMX-6010
-
(SMX-6010) Checking the Cross-section Image and CT Calibr...
Use the provided "grid mesh phantom" (part No. 362-84302) when checking thecross-section image. 1. Click [Change Sample]. 2. Set the grid mesh... Show Detail
- No：8604
- Date of Issue：2022/04/28 13:16
- Category： Xslicer SMX-6010
- Brached FAQ
-
(SMX-1010/1020) Performing Flat Panel Detector Calibration
Flat panel detector calibration is a function used to reduce unevenness and noise in theimage. Perform calibration if unevenness or noise in the image becom... Show Detail
- No：8620
- Date of Issue：2022/04/28 10:30
- Category： Xslicer SMX-1010/1020
-
(SMX-6010) Performing Flat Panel Detector Calibration
Flat panel detector calibration is a function for reducing unevenness and noise in theimage. Perform calibration if unevenness or noise in the image becomes... Show Detail
- No：8603
- Date of Issue：2022/04/28 10:30
- Category： Xslicer SMX-6010
-
(SMX-6010) Checking the Operating Time of the Turbomolecu...
The operating time of the turbomolecular pump and diaphragm pump can be checkedusing the [RUN TIME] indicator on the right side of the instrument. The... Show Detail
- No：8602
- Date of Issue：2022/04/28 10:07
- Category： Xslicer SMX-6010
-
Follow the procedure described below when the X-ray generator requires aging. NOTE: Use this function in administrator mode. Click here for "(SMX-6010... Show Detail
- No：8601
- Date of Issue：2022/04/28 10:04
- Category： Xslicer SMX-6010
-
(SMX-6010) Adjusting the Focus
Adjust the focus when the image is blurry. Use the provided "grid mesh phantom" (part No. 362-84302) when adjusting the focus. NOTE: Use this function in... Show Detail
- No：8600
- Date of Issue：2022/04/28 09:49
- Category： Xslicer SMX-6010
41-50 of Total 61