Beam alignment is an adjustment function for increasing image brightness. Although the beam alignment is adjusted autom

Adjust the focus when the image is blurry. Use the provided "grid mesh phantom" (part No. 362-84302) when adjusting t

Follow the procedure described below when the X-ray generator requires aging. NOTE: Use this function in administrato

The operating time of the turbomolecular pump and diaphragm pump can be checkedusing the [RUN TIME] indicator on the rig

Flat panel detector calibration is a function for reducing unevenness and noise in theimage. Perform calibration if une

Flat panel detector calibration is a function used to reduce unevenness and noise in theimage. Perform calibration if u

Use the provided "grid mesh phantom" (part No. 362-84302) when checking thecross-section image. 1. Click [Change

When X-ray output is difficult, the interior of the vacuum chamber may be dirty causingelectrical discharges. In this ca

NOTE: • Use this function in administrator mode. Click here for "(SMX-6010) Switching to Administrator Mode".

The pre-operation check/initialization involves checking the front door, checking the X-raygenerator, and returning the

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > Non-Destructive Testing (NDT) Systems

Keyword Search

Non-Destructive Testing (NDT) Systems

inspeXio SMX-225CT(21)

Frequently Referenced FAQ

Latest FAQ

FAQ within [ Non-Destructive Testing (NDT) Systems ]

11-20 of Total 61

≪ 2 / 7page ≫

(SMX-6010) Adjusting the Beam Alignment

Beam alignment is an adjustment function for increasing image brightness. Although the beam alignment is adjusted automatically after aging at instrument st... Show Detail
- No：8599
- Date of Issue：2022/04/28 09:29
- Category： Xslicer SMX-6010
(SMX-6010) Adjusting the Focus

Adjust the focus when the image is blurry. Use the provided "grid mesh phantom" (part No. 362-84302) when adjusting the focus. NOTE: Use this function in... Show Detail
- No：8600
- Date of Issue：2022/04/28 09:49
- Category： Xslicer SMX-6010
(SMX-6010) Performing Aging

Follow the procedure described below when the X-ray generator requires aging. NOTE: Use this function in administrator mode. Click here for "(SMX-6010... Show Detail
- No：8601
- Date of Issue：2022/04/28 10:04
- Category： Xslicer SMX-6010
(SMX-6010) Checking the Operating Time of the Turbomolecu...

The operating time of the turbomolecular pump and diaphragm pump can be checkedusing the [RUN TIME] indicator on the right side of the instrument. The... Show Detail
- No：8602
- Date of Issue：2022/04/28 10:07
- Category： Xslicer SMX-6010
(SMX-6010) Performing Flat Panel Detector Calibration

Flat panel detector calibration is a function for reducing unevenness and noise in theimage. Perform calibration if unevenness or noise in the image becomes... Show Detail
- No：8603
- Date of Issue：2022/04/28 10:30
- Category： Xslicer SMX-6010
(SMX-1010/1020) Performing Flat Panel Detector Calibration

Flat panel detector calibration is a function used to reduce unevenness and noise in theimage. Perform calibration if unevenness or noise in the image becom... Show Detail
- No：8620
- Date of Issue：2022/04/28 10:30
- Category： Xslicer SMX-1010/1020
(SMX-6010) Checking the Cross-section Image and CT Calibr...

Use the provided "grid mesh phantom" (part No. 362-84302) when checking thecross-section image. 1. Click [Change Sample]. 2. Set the grid mesh... Show Detail
- No：8604
- Date of Issue：2022/04/28 13:16
- Category： Xslicer SMX-6010
- Brached FAQ
(SMX-6010) Cleaning the Vacuum Chamber

When X-ray output is difficult, the interior of the vacuum chamber may be dirty causingelectrical discharges. In this case, clean the interior of the vacuum ... Show Detail
- No：8605
- Date of Issue：2022/04/28 13:28
- Category： Xslicer SMX-6010
(SMX-6010) Replacing the Filament

NOTE: • Use this function in administrator mode. Click here for "(SMX-6010) Switching to Administrator Mode". • Even when [Status] under [Fila... Show Detail
- No：8595
- Date of Issue：2022/04/28 13:30
- Category： Xslicer SMX-6010
- Brached FAQ
(SMX-6010) Performing the Pre-Operation Check/Initialization

The pre-operation check/initialization involves checking the front door, checking the X-raygenerator, and returning the stage to the origin point. Perform th... Show Detail
- No：8591
- Date of Issue：2022/04/28 13:34
- Category： Xslicer SMX-6010

11-20 of Total 61

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.