Part Number:347-24149-01 Illumination Lamp 1. Remove upper cover. 2.Remove lamp ASSY and install new

Replace the battery on the CPU board. Contact a Shimadzu sales or service representative.

1.The room temperature has dropped below freezing. This is not a malfunction. The clock IC does not operate at tempe

Adjust the magnification as per section "Replacing and Adjusting the Objective Lens". Click here for "(HMV) Replaci

Check the test conditions. The effect of noise can result in settings with abnormal values. Ifthe test condition valu

Possible Causes: 1. Effects of vibrations Vibrations will have a significant effect at test forces of 98.07 mN or l

Check the lamp as "Replacing the Illumination Lamp". If it is burnt out, replace it. If despite this it still will not

After adjusting the focus using the microscope, if the indenter touches the sample whenthe turret rotates, the indenter

When the focus is adjusted with the microscope, and the indenter is rotated by the turretin preparation for testing, the

If the indentation is not positioned at the center of the field of view, as in below,adjust the positioning as "Centerin

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > Materials Testing & Inspection > Hardness Tester

Keyword Search

Hardness Tester

Frequently Referenced FAQ

Latest FAQ

FAQ within [ Hardness Tester ]

21-30 of Total 38

≪ 3 / 4page ≫

(DUH) Illumination Lamp Replacement

Part Number:347-24149-01 Illumination Lamp 1. Remove upper cover. 2.Remove lamp ASSY and install new lamp ASSY. 3.Close the top cover, an... Show Detail
- No：7514
- Date of Issue：2021/12/06 10:05
- Category： Dynamic Ultra-micro Hardness Tester(DUH)
(HMV) The ready lamp and the running lamp blink

Replace the battery on the CPU board. Contact a Shimadzu sales or service representative. Show Detail
- No：7506
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the clock time is incorrect

1.The room temperature has dropped below freezing. This is not a malfunction. The clock IC does not operate at temperatures below freezing. 2.The ... Show Detail
- No：7505
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the indentation readings are abnormal

Adjust the magnification as per section "Replacing and Adjusting the Objective Lens". Click here for "(HMV) Replacing and Adjusting the Objective Lens".... Show Detail
- No：7504
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the test force or retention time is different th...

Check the test conditions. The effect of noise can result in settings with abnormal values. Ifthe test condition values are as expected but the values dur... Show Detail
- No：7503
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the standard value of a hardness test piece does...

Possible Causes: 1. Effects of vibrations Vibrations will have a significant effect at test forces of 98.07 mN or less. Ensure that thearea around the i... Show Detail
- No：7502
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the illumination lamp does not light

Check the lamp as "Replacing the Illumination Lamp". If it is burnt out, replace it. If despite this it still will not light, contact a Shimadzu sales or s... Show Detail
- No：7501
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the tip of the indenter is too close to the sample

After adjusting the focus using the microscope, if the indenter touches the sample whenthe turret rotates, the indenter setscrew may be loose. Follow the pro... Show Detail
- No：7500
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV) If the indenter height is abnormal

When the focus is adjusted with the microscope, and the indenter is rotated by the turretin preparation for testing, the indenter height will need to be adju... Show Detail
- No：7499
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)
(HMV)If the indentation is not positioned at the center o...

If the indentation is not positioned at the center of the field of view, as in below,adjust the positioning as "Centering theIndentation". Click here for ... Show Detail
- No：7498
- Date of Issue：2021/12/06 10:05
- Category： Micro Hardness Tester(HMV)

21-30 of Total 38

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.