FAQ - Frequently Asked Questions
- Products Search > GC
Keyword Search
Frequently Referenced FAQ
FAQ within [ GC ]
-
SCD out pyrotube use time warn.[Error Code:9074]
Replace the outer pyrotube and then reset the counter. ※Replace the outer pyrotube MaintenanceHelp_SCD-Outer-Pyrotube-Replacement.pdf ※Reset... Show Detail
- No：5954
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/03 15:53
- Category： Error/Warning
-
SCD in pyrotube use time warn[Error Code:9073]
Replace the inner pyrotube and then reset the counter. ※Replace the inner pyrotube MaintenanceHelp_SCD-Inner-Pyrotube-Replacement.pdf ※ Rese... Show Detail
- No：5953
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/03 15:00
- Category： Error/Warning
-
Processing, unable to start[Error Code:9054]
Wait for the analysis to finish before starting the next analysis. Show Detail
- No：5952
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/03 14:40
- Category： Error/Warning
-
Not execute this operation [Error Code:9061]
The following operation was executed while theGC stopped. • Ignition/Illumination • FTD Feedback • Start analysis • Batch • Clean Up • PREP RUN • ... Show Detail
- No：5951
- Date of Issue：2021/05/18 15:37
- Category： Error/Warning
- Brached FAQ
-
SCD ozone scrub. use time warn. [Error Code:9072]
The risk of ozone entering the exhaust from the vacuum pump increases. Replace the filling materials of the ozone scrubber and then reset the counter. ... Show Detail
- No：5950
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/09 16:51
- Category： Error/Warning
-
SCD vacuum pump use time warn. [Error Code:9071]
Replace or maintain the vacuum pump and then reset the counter. SCD vacuum pump replacement MaintenanceHelp_SCD-Vacuum-Pump-Onspection.pdf Cou... Show Detail
- No：5949
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/09 16:40
- Category： Error/Warning
-
Gas Selector# purge set point not reached [Error Code:234...
Check whether gas is supplied and whether gas is not leaking from connections. Gas leaks may be occurring in several locations (other than displayed site). Show Detail
- No：5920
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/12 01:28
- Category： Error/Warning
-
Gas Selector# main set point not reached [Error Code:2346...
Check whether gas is supplied and whether gas is not leaking from connections. Gas leaks may be occurring in several locations (other than displayed site). Show Detail
- No：5919
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/12 01:27
- Category： Error/Warning
-
Flow# press/flow offset value is shifted [Error Code:2338...
An error may occur on the pressure sensor. Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative. Show Detail
- No：5918
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/12 01:26
- Category： Error/Warning
-
Flow# valve control irregularity [Error Code:2322 2323 23...
The valve of the flow controller or board may have failed. Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/servic... Show Detail
- No：5917
- Date of Issue：2021/05/18 15:37
- Last Updated：2021/06/12 01:24
- Category： Error/Warning
71-80 of Total 253