Check that the BID detector gas supply pressure is within the range below. Check that the supply pressure is sufficie

Check that the gas main valve is open. Check that the gas supply pressure is within the range below. Check that the

Check that the hydrogen gas supply pressure is within the range below. Check that the supply pressure is sufficient f

Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative to as

Set the furnace temperature at 750 °C or higher.

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > GC

Keyword Search

GC

Consumables(6)

Frequently Referenced FAQ

Latest FAQ

FAQ within [ GC ]

241-250 of Total 255

≪ 25 / 26page ≫

DCG APC are not ready[Error Code:4212]

Check that the BID detector gas supply pressure is within the range below. Check that the supply pressure is sufficient for the BID detector gas to flow. ... Show Detail
- No：6035
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/10 09:36
- Category： Error/Warning
DCG flow rate is not enough[Error Code:4213]

Check that the gas main valve is open. Check that the gas supply pressure is within the range below. Check that the supply pressure is sufficient for the... Show Detail
- No：6034
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:59
- Category： Error/Warning
SCD oxygen primary pressure is not enough[Error Code:6146]

Check that the gas main valve is open. Check that the gas supply pressure is within the range below. Check that the supply pressure is sufficient for the... Show Detail
- No：6033
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:52
- Category： Error/Warning
SCD hydrogen primary pressure is not enough[Error Code:6147]

Check that the hydrogen gas supply pressure is within the range below. Check that the supply pressure is sufficient for the hydrogen gas to flow. Check t... Show Detail
- No：6032
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:41
- Category： Error/Warning
SCD WDT error[Error Code:6148]

Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative to ask for part replacement. Show Detail
- No：6031
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:37
- Category： Error/Warning
SCD heater relay has been fixed to ON[Error Code:6149]

Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative to ask for part replacement. Show Detail
- No：6030
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:37
- Category： Error/Warning
SCD flow controler#1 was not connected[Error Code:6151]

Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative to ask for part replacement. Show Detail
- No：6029
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:36
- Category： Error/Warning
SCD flow controler#2 was not connected[Error Code:6152]

Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative to ask for part replacement. Show Detail
- No：6028
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:34
- Category： Error/Warning
SCD PMT light was leaked[Error Code:6154]

Turn off the main power of the instrument, stop gas supply, and contact your Shimadzu sales/service representative to ask for part replacement. Show Detail
- No：6027
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/07 16:59
- Category： Error/Warning
SCD furnace temperature is low[Error Code:6155]

Set the furnace temperature at 750 °C or higher. Show Detail
- No：6026
- Date of Issue：2021/05/18 15:33
- Last Updated：2021/06/03 12:30
- Category： Error/Warning

241-250 of Total 255

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.