Consumable Part No. 228-72570-01 Air filter 1. Remove the filter holder (A) on the right side by pressing its rig

Consumable Parts Number:228-45707-91 SUS Filter Element « Below are the changes for SI

Part No. 228-53924-05 Dust Filter 1. Turn OFF power to the instrument. 2. Open the filter cover (A) and th

Check whether the noise disappears when solvent delivery stops. Check the solvent delivery flow status (pulsation). If

Check the light level. If the light level is low even with an air cell or if the lamp has been operated for more than

Specify an appropriate range value. Set [LAMP] to [D2]. The light source lamp illuminates. Click the [ZERO] button i

Click [PURGE] to purge the bubbles. Alternatively, connect a syringe to the drain tube connection port to suction out th

Check for leakage from cell inlet and outlet pipe connections and from the cell window. If there is leakage, disassemble

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > HPLC

Keyword Search

HPLC

System(13)

Frequently Referenced FAQ

Latest FAQ

FAQ within [ HPLC ]

71-80 of Total 929

≪ 8 / 93page ≫

Maintenance for CTO-40C/S

Consumable Part No. 228-72570-01 Air filter 1. Remove the filter holder (A) on the right side by pressing its right and left knobs (a). 2. ... Show Detail
- No：4339
- Date of Issue：2020/12/03 13:45
- Category： Column Oven
- Brached FAQ
Maintenance for SIL-40 series (Video)

Consumable Parts Number:228-45707-91 SUS Filter Element « Below are the changes for SIL-40C XSi» • Ring(B) is added to S... Show Detail
- No：4320
- Date of Issue：2020/12/03 13:40
- Category： Autosampler
- Brached FAQ
Maintenance for SPD-M40 (Video)

Part No. 228-53924-05 Dust Filter 1. Turn OFF power to the instrument. 2. Open the filter cover (A) and then remove the filter (B). ... Show Detail
- No：4309
- Date of Issue：2020/12/03 13:04
- Last Updated：2020/12/04 14:53
- Category： Detector
- Brached FAQ
Maintenance for SPD-40(V) (Video)

Show Detail
- No：4301
- Date of Issue：2020/12/03 11:16
- Last Updated：2020/12/04 14:53
- Category： Detector
- Brached FAQ
Sawtooth-shaped noise occurs

Check whether the noise disappears when solvent delivery stops. Check the solvent delivery flow status (pulsation). If pulsation is large, rinse the flow ch... Show Detail
- No：4300
- Date of Issue：2020/12/03 11:06
- Category： Common , Detector , Solvent Delivery Module
- Brached FAQ
Cyclic spiky noise is output

Check whether the noise disappears when solvent delivery stops. Check the solvent delivery flow status (pulsation). If pulsation is large, rinse the flow ch... Show Detail
- No：4299
- Date of Issue：2020/12/03 11:05
- Category： Common , Detector , Solvent Delivery Module
- Brached FAQ
Noise level is high

Check the light level. If the light level is low even with an air cell or if the lamp has been operated for more than 2000 hours, then replace the lamp. ... Show Detail
- No：4298
- Date of Issue：2020/12/03 11:03
- Category： Detector
- Brached FAQ
The baseline does not change

Specify an appropriate range value. Set [LAMP] to [D2]. The light source lamp illuminates. Click the [ZERO] button in the [RUN] window. Adjust the zero p... Show Detail
- No：4297
- Date of Issue：2020/12/03 11:01
- Category： Detector
- Brached FAQ
The baseline undulates with the pump stroke

Click [PURGE] to purge the bubbles. Alternatively, connect a syringe to the drain tube connection port to suction out the bubbles. Click here for Manual P... Show Detail
- No：4296
- Date of Issue：2020/12/03 11:00
- Category： Common , Solvent Delivery Module
- Brached FAQ
The baseline shifts

Check for leakage from cell inlet and outlet pipe connections and from the cell window. If there is leakage, disassemble and clean the cell. If there is lo... Show Detail
- No：4295
- Date of Issue：2020/12/03 10:59
- Category： Common
- Brached FAQ

71-80 of Total 929

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.