FAQ - Frequently Asked Questions

  • Font Size
  • S
  • M
  • L

Keyword Search

You can search two or more words separated by a space. 
Separate keywords with sapce to search for ALL.
Separate with "｜" to search for EITHER words.
And having "-" at the start of the word will EXCLUDE it.

Frequently Referenced FAQ

Latest FAQ

FAQ within [ Universal Testing Machine(UH) ]

1-10 of Total 16

≪ 1 / 2page ≫

  • (UH) Starting and Stopping the Machine

    1. Make sure that there are no obstacle around the testing machine, and then turn ON the powerswitch. 2. Turn ON the key switch to supply power. ... Show Detail

    • No：7532
    • Date of Issue：2021/12/02 13:24
    • Brached FAQ

  • (UH) Raising / Lowering the Lower Crosshead

    CAUTION:Make sure that there is no obstacle, tools, etc. on the upper or lower surface ofthe crosshead before operating the crosshead. Also, since the ... Show Detail

    • No：7533
    • Date of Issue：2021/12/02 13:38

  • (UH) Raising / Lowering the Table

    Set the Manual mode before manually raising/lowering the table. (Click)Using the load control (Manual Control) knob The load control knob can... Show Detail

    • No：7534
    • Date of Issue：2021/12/02 13:38

  • (UH) Setting up the touch panel

    Before operating the testing machine, you need to perform the initial setting of the LCD display. The touch panel must be configured so that the keys displa... Show Detail

    • No：7535
    • Date of Issue：2021/12/02 13:38

  • (UH) Repositioning the Upper Crosshead

    WARNING:Be sure to install the lower fixture so that it is seated correctly in the set ring. The upper fixture may come off during tests if the lower f... Show Detail

    • No：7536
    • Date of Issue：2021/12/02 15:17
    • Brached FAQ

  • (UH) Lubrication (Greasing)

    1. Apply grease to the screw rods. Be sure to completely remove the old grease before applynew grease. (Monthly) 2. Apply machine oil or spindle oil to ... Show Detail

    • No：7544
    • Date of Issue：2021/12/02 15:17
    • Brached FAQ

  • (UH) Levelness Inspection

    1. Levelness inspection of the load frame 1)Place a spirit level near the center of the table top and measure the levelness of the table in all dire... Show Detail

    • No：7545
    • Date of Issue：2021/12/02 15:17
    • Brached FAQ

  • (UH) Using the Grip jaws for Tensile Tests

    CAUTION:The grip jaws have sharp edges to allow grasping of the specimen. When handling the grip jaws, be careful not to cut your fingers or hand. ... Show Detail

    • No：7537
    • Date of Issue：2021/12/02 15:53
    • Brached FAQ

  • (UH) Mounting the platens for Compression Tests

    CAUTION:When attaching the compression platen, be carefull not to have your fingerscaught. Be carefull not to fall the compression platen. Compression pl... Show Detail

    • No：7538
    • Date of Issue：2021/12/02 16:09
    • Brached FAQ

  • (UH) Electronic Calibration (E-CAL)

    The electronic calibration (E-CAL) is required once per day before the daily startup of the testingmachine. Even so, this calibration must be done immediatel... Show Detail

    • No：7539
    • Date of Issue：2021/12/02 16:22

1-10 of Total 16

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.