The limit of quantitation (LOQ) and limit of detection (LOD) are calculated by converting the standard deviation of the

The following conditions are assumed: ・An AS-10 autosampler is used ・A peristaltic pump is not used ・Sample introduction

The appropriate approach depends on the measurement requirements and the type of organic solvent. 1. Radial view: Oxyg

Non-spectral interferences may occur when a sample has a high matrix concentration. These include physical interferences

If the filter is clogged, remove the cover on the left side of the ASC-9800 and clean the filter. If the filter has dete

If the flow rate of the peristaltic pump used to supply rinse solution decreases, replace the tubing in the peristaltic

1. Insert the nozzle (Parts number: 206-50290-91) into the nozzle hole located on the arm. 2. Lower the nozzle tip by 1

• The blank liquid is dirty. • The torch is dirty. • The chamber is dirty. Click here for "Replacing and Inspecting Gl

• Wipe off the water droplets with gauze or some otherappropriate material and ignite the plasma. • Checks that the inst

• The ICPEinstallation location does not meetrequirements related to installation location or facilities. • One of the c

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > Elemental Analysis > Inductively Coupled Plasma Emission Spectroscopy(ICP) > Multi type(ICPE)

Keyword Search

Frequently Referenced FAQ

Latest FAQ

FAQ within [ Multi type(ICPE) ]

1-10 of Total 27

≪ 1 / 3page ≫

(ICPE) The limit of quantitation (LOQ)

The limit of quantitation (LOQ) and limit of detection (LOD) are calculated by converting the standard deviation of the intensity of the calibration blank sa... Show Detail
- No：12477
- Date of Issue：2026/08/19 11:30
- Last Updated：2026/08/20 12:57
(ICPE) How should rinse time be determined?

The following conditions are assumed: ・An AS-10 autosampler is used ・A peristaltic pump is not used ・Sample introduction tube length: 40 cm (See the red l... Show Detail
- No：12473
- Date of Issue：2026/08/19 09:41
- Brached FAQ
(ICPE) Oxygen requirement when introducing an organic sol...

The appropriate approach depends on the measurement requirements and the type of organic solvent. 1. Radial view: Oxygen introduction not required With... Show Detail
- No：12471
- Date of Issue：2026/08/19 09:10
- Last Updated：2026/08/20 12:55
(ICPE) About internal standard (IS)

Non-spectral interferences may occur when a sample has a high matrix concentration. These include physical interferences and ionization interferences. Physic... Show Detail
- No：12257
- Date of Issue：2026/05/08 13:42
- Brached FAQ
(ICPE) Filter Cleaning and Replacement (Autosampler)

If the filter is clogged, remove the cover on the left side of the ASC-9800 and clean the filter. If the filter has deteriorated, replace it with a new filt... Show Detail
- No：6742
- Date of Issue：2021/08/03 10:56
- Brached FAQ
(ICPE) Replacing the Peristaltic Pump Tubing (Autosampler)

If the flow rate of the peristaltic pump used to supply rinse solution decreases, replace the tubing in the peristaltic pump according to the following proce... Show Detail
- No：6741
- Date of Issue：2021/08/03 10:51
- Brached FAQ
(ICPE) Mounting the Nozzle (Autosampler)

1. Insert the nozzle (Parts number: 206-50290-91) into the nozzle hole located on the arm. 2. Lower the nozzle tip by 103 mm from the bottom of the arm an... Show Detail
- No：6740
- Date of Issue：2021/08/03 10:21
- Brached FAQ
(ICPE) The spectral intensity for elements is high even w...

• The blank liquid is dirty. • The torch is dirty. • The chamber is dirty. Click here for "Replacing and Inspecting Glassware, Sample Introduction Tub... Show Detail
- No：6739
- Date of Issue：2021/07/30 10:11
(ICPE) Condensation occurs on the RF coil or the cooling ...

• Wipe off the water droplets with gauze or some otherappropriate material and ignite the plasma. • Checks that the installation location meets the installa... Show Detail
- No：6738
- Date of Issue：2021/07/30 10:11
- Last Updated：2021/10/04 10:07
(ICPE) The spectral intensity is unstable

• The ICPEinstallation location does not meetrequirements related to installation location or facilities. • One of the causes listed for problem "The spectr... Show Detail
- No：6737
- Date of Issue：2021/07/30 10:11

1-10 of Total 27

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Technology Inc.