Improper installation of the filter element. Reinstall the filter element correctly. When this is done, check the O-r

Disabled cooler, drain pump failure. Replace the cunsumable parts. Click here for "Maintenance (Replacement of con

Clogged filter. Frozen cooler. Too much throttled needle valve. Mixed dust into the pump. Replace the consumable part

Disconnected piping. Broken pump. Check the piping after the pump for disconnection. About the pump manintenance,

• There is a problem with thepump.→ Replace the pump diaphragm orreplace thepump completely. Contact a Shimadzu sales or

• There is alarge change inambient temperature.→ Select a location with as little possible changein temperature. •

• The ground is not complete,→ Connect a ground having a resistance of no more than 100 ohms. • There is a large so

• O2 sensor may be deteriorated. Contact a Shimadzu sales or service representative.

• Any leakage from the standard gas inlet?→Attach a hose clamp to the standard gas inlet to prevent leakage. • Any

Has temperature of ozone deactivator risen. (The ozone deactivator is normal if it is warm to the touch.) Contact a S

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > Continuous Monitoring Analysis

Keyword Search

Frequently Referenced FAQ

Latest FAQ

FAQ within [ Continuous Monitoring Analysis ]

1-10 of Total 17

≪ 1 / 2page ≫

(GAS) The indication of the connected analyzer is too low...

Improper installation of the filter element. Reinstall the filter element correctly. When this is done, check the O-ring for any damage. Click here for... Show Detail
- No：6827
- Date of Issue：2021/08/20 13:39
(GAS) The water drops from the gas outlet (CFP-8000)

Disabled cooler, drain pump failure. Replace the cunsumable parts. Click here for "Maintenance (Replacement of consumables)". Show Detail
- No：6826
- Date of Issue：2021/08/20 13:39
(GAS) The gas flows only at 1L/min (CFP-8000)

Clogged filter. Frozen cooler. Too much throttled needle valve. Mixed dust into the pump. Replace the consumable parts. Click here for "Maintenance (Re... Show Detail
- No：6825
- Date of Issue：2021/08/20 13:39
(GAS) The gas dose not flow at all (CFP-8000)

Disconnected piping. Broken pump. Check the piping after the pump for disconnection. About the pump manintenance, click here for "Maintenance (Replacem... Show Detail
- No：6824
- Date of Issue：2021/08/20 13:39
(GAS) Gas does not flow into the flow meter (CGT-7100)

• There is a problem with thepump.→ Replace the pump diaphragm orreplace thepump completely. Contact a Shimadzu sales or service representative. • There... Show Detail
- No：6823
- Date of Issue：2021/08/20 11:25
(GAS) The indicator drifts (CGT-7100)

• There is alarge change inambient temperature.→ Select a location with as little possible changein temperature. • The inner surface of the cell isdirty... Show Detail
- No：6822
- Date of Issue：2021/08/20 11:25
(GAS) The indicator values fluctuate or exhibit noise (CG...

• The ground is not complete,→ Connect a ground having a resistance of no more than 100 ohms. • There is a large source ofvibration in the vicinity.→ Re... Show Detail
- No：6821
- Date of Issue：2021/08/20 11:25
(GAS) O2 sensor's response becomes slow (NOA-7100)

• O2 sensor may be deteriorated. Contact a Shimadzu sales or service representative. Show Detail
- No：6820
- Date of Issue：2021/08/20 11:25
(GAS) Response is slow when performing span calibration o...

• Any leakage from the standard gas inlet?→Attach a hose clamp to the standard gas inlet to prevent leakage. • Any leakage from the piping inside the in... Show Detail
- No：6818
- Date of Issue：2021/08/20 11:25
- Last Updated：2021/08/23 12:49
(GAS) Ozone odor is evident (NOA-7100)

Has temperature of ozone deactivator risen. (The ozone deactivator is normal if it is warm to the touch.) Contact a Shimadzu sales or service representati... Show Detail
- No：6817
- Date of Issue：2021/08/20 11:25

1-10 of Total 17

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.