1. The room temperature might be hight (such as over 40ºC). Check environmental conditions at the installation site.

1. Turn on the filament after solvent has completely eluted. If peaks elute before the solvent, use a time program to tu

Cause 1: Carrier gas flows? Action 1: If carrier gas is not flowing, please let the carrier gas flow. Cause 2:

1. Error message displayed when standard is introduced. Checks that Filament ON Errors. 2. "Initialization Er

• "Filament consumed" message appears. Filament installation is not correctly. Filament malfunction. Click h

Cause 1: Does Rotary Pump1 (RP1) operate? Action 1: Connect the RP1 power cable to the back panel of the MS, and turn

1. PC and MS or MS and GC connected properly? All connections must be made properly 2. Is GC power on? Turn on GC pow

Normal LED Indications: Switch MS Unit → All 3 LED light → Green and Red LED goes out → Yellow LED remains ON

This section describes how to check the instrument for leaks. If an air leak is clearly present, locate the leak as desc

For power outages of 10 minutes or less, normally no particular procedure is required as long as the [Vacuum Restart Mod

FAQ - Frequently Asked Questions

Font Size
S
M
L

Products Search > GC-MS

Keyword Search

GC-MS

Setting(6)

Frequently Referenced FAQ

Latest FAQ

FAQ within [ GC-MS ]

31-40 of Total 56

≪ 4 / 6page ≫

(GCMS) RF Temperature Control Error

1. The room temperature might be hight (such as over 40ºC). Check environmental conditions at the installation site. 2. The Q1 or Q3 RF temperature contro... Show Detail
- No：4713
- Date of Issue：2020/12/17 16:46
- Category： Troubleshooting
(GCMS) "Detector saturated" message appears during analysis

1. Turn on the filament after solvent has completely eluted. If peaks elute before the solvent, use a time program to turn the filament off and on. 2. Dec... Show Detail
- No：4712
- Date of Issue：2020/12/17 16:43
- Category： Troubleshooting
(GCMS) No peaks appear, or peaks are too small

Cause 1: Carrier gas flows? Action 1: If carrier gas is not flowing, please let the carrier gas flow. Cause 2: Carrier gas leaks. Action 2: Tigh... Show Detail
- No：4711
- Date of Issue：2020/12/17 16:38
- Category： Troubleshooting
(GCMS) Autotuning and Analysis Errors

1. Error message displayed when standard is introduced. Checks that Filament ON Errors. 2. "Initialization Error" message appears. Whenstandar... Show Detail
- No：4710
- Date of Issue：2020/12/17 16:28
- Category： Troubleshooting
(GCMS) Filament ON Errors

• "Filament consumed" message appears. Filament installation is not correctly. Filament malfunction. Click here for Filament Replacement Procedur... Show Detail
- No：4709
- Date of Issue：2020/12/17 16:18
- Category： Troubleshooting
(GCMS) Vacuum System Auto Startup Errors

Cause 1: Does Rotary Pump1 (RP1) operate? Action 1: Connect the RP1 power cable to the back panel of the MS, and turn on the RP1 switch. If not resolve... Show Detail
- No：4708
- Date of Issue：2020/12/17 16:03
- Category： Troubleshooting
(GCMS) GCMSsolution Software Startup Errors

1. PC and MS or MS and GC connected properly? All connections must be made properly 2. Is GC power on? Turn on GC power supply and restart. 3. Is MS po... Show Detail
- No：4707
- Date of Issue：2020/12/17 15:54
- Category： Troubleshooting
(GCMS) Error status indicated by LED on MS

Normal LED Indications: Switch MS Unit → All 3 LED light → Green and Red LED goes out → Yellow LED remains ON LED Error Indications Yellow LED... Show Detail
- No：4706
- Date of Issue：2020/12/17 15:49
- Category： Troubleshooting
(GCMS) Checking for Leaks

This section describes how to check the instrument for leaks. If an air leak is clearly present, locate the leak as described in "2. MS Vacuum Leak Check", a... Show Detail
- No：4705
- Date of Issue：2020/12/17 15:41
- Category： Maintenance
(GCMS) Measurres durriing Powerr Outtage

For power outages of 10 minutes or less, normally no particular procedure is required as long as the [Vacuum Restart Mode] checkbox is selected in the window... Show Detail
- No：4704
- Date of Issue：2020/12/17 13:21
- Category： Troubleshooting

31-40 of Total 56

To Top of Page

This site uses the FAQ system "PKSHA FAQ", which is a product of PKSHA Communication Inc.